On SIG Down we must not fail a call instead try hunting for another.
The only time we can fail the call and not bother hunting is
if sng_cc_resource_check fails.
Took out configuration retry as the config code is now
fixed in sng_ss7 library. Transaction id fix.
Unit Tested:
NSG UP -- start full load
kill NSG
NSG UP again on full load
make sure it comes up fine.
before hanging up the freetdm channel by force
seems to have a memory leak. I have increased the timeout
to 30sec and made the print statement WARNING level.
Where FS does not hangup the channel with in 3sec.
Without this fix, it was possible that 2 FS sessions
use the single span/chan freetdm session.
Merged the feature from git master of freetdm
SUSPEND will not only change the return state in few
cases.
I have retested all test cases from previous 2 commits.
What is missing is timer for each Tx Event. RSC,BLO,UBL.
Its possible to loose a message from Slave via relay to Master.
If that ever occours we will not know what state we are in.
Thus we need a timer that will re-transmit a packet if
it does not get acknowledged.
changed parameter name from cpu_reset_alarm_threshold to cpu_clear_alarm_threshold
(old parameter name still valid for backwards compatibility in configuration files)
used to clear ckt_flags, this was wrong.
if ctk_flags are blindly cleard a PAUSE might be cleared.
changed the code to clear only TX RESET and try to reset again.
Release Collision
If we get out of sync with other side we must
reset the circuit.
This condition occoured at 1+3 test box
Local Management Block
Its possible for stack to send us a BLO indicating to us
that we are local blocked. This case never worked and
we would get stuck there forever.
If we never manaully sent a LOCAL block, the BLO from
the stack will be acked and then unblocked.
This condition occoured at 1+3 test box
From previous commit, failed to clear the done flag _DN
which cause SUSPEND to think that there was a block
pending, causing state to remain in RESTART
S UP -> relay down -> Tx AIS -> relay up -> Tx AIS off
-> confirm all back up
-> In this condition BLO will not go out due to PAUSE
S UP -> Tx AIS -> relay down -> Tx AIS off -> relay up
-> confirm all back up
-> In this condition UBL will not go out due to PAUSE
Visually status of channels will only be DOWN once all resets/blocks are cleared.
Therefore if any reset/block is active on a channel, the channel state will be in RESTART not DOWN.
Logic Change
SUSPENDED
-> Originally used as intermediate state. Purpose is to handle a condition
from any state and go back to the previous state.
Conditions: such as block/ucic.
-> Updated logic is that SUSPEND will be smart enough not to
go back to just any state. SUSPEND will only go back to
UP - if call is still up
RESTART - if for any reason singaling is not up due to
blocks/resets/etc...
DOWN - if signaling is UP - no resets/blocks
In this case we avoid infinite loops due to state jumping
from STATE->SUSPEND->STATE->SUSPEND
HANGUP_COMPLETE
-> If call is in use and a RESET comes on a call
the RESTART state will first try the HANGUP_COMPLETE state.
HANGUP_COMPLETE will Tx RSC and wait for it.
Reset Response handle was updated if current state HANGUP/HANGUP_COMPLETE
go back to RESTART state. Which will call HANGUP COMPLETE due to
channel in usage and HANDLE_COMPLETE will clear RESET condition and go back to DOWN
TERMINATING
-> This state is used to hangup a call. Sends a signal to FS.
-> Usually TERMINATING state stays in TERMINATING until FS comes back.
-> I added a condition in case of RESET on the line though TERMINATING
will go back to RESTART.
This allows us to process RESET commands even though we are
in the middle of hanging up.
Block Handler
If BLO is received on circuit is already blocked,
we failed to trasmit BLA. We should always ack the BLO
even though it was alrady in blocked state.
Fixed & Tested
S UP --> place call --> relay down --> hangup --> relay up-->
Confirm that call is hungup properly.
In this condition, on relay up the circuit is put into RESET.
Since circuit is still in use, it will HANGUP first, then RESET
then clear pending BLOCK.
S UP --> place call -> Tx RSC on call.
Used to cause infitie loop
Confirm call is cleard properly
Re-Tested
S UP --> place call -> Rx RSC on call
Confirm call is cleard properly
S UP --> place call -> Rx BLO -> hangup -> place call
Confirm call cannot be placed
Tx UBL
Confirm call can be placed
S UP --> place call -> Rx BLO -> Tx BLO -> hangup -> place call
Confirm call cannot be placed
Tx UBL
Confirm call cannot be placed
Rx UBL
Confirm call can be placed
S UP --> place call -> relay down --> Rx BLO on channel from telco
--> relay up
Confirm that relay detects the BLO channels even though relay was down
Tx AIS -> S Start -> Confirm HW block -> Tx AIS off
-> Confirm hw block clear and UP
S UP -> Tx AIS -> Confirm HW block -> Tx AIS off
-> confirm hw block clear and UP
S UP -> relay down -> Tx AIS -> relay up -> Tx AIS off
-> confirm all back up
-> In this condition BLO will not go out due to PAUSE
S UP -> Tx AIS -> relay down -> Tx AIS off -> relay up
-> confirm all back up
-> In this condition UBL will not go out due to PAUSE
M UP -> S UP
M Down -> S UP -> M UP
M UP -> S UP -> relay down -> relay up
M UP -> S UP -> Kill M -> M UP
M Up -> S UP -> relay down -> M link down -> relay up -> M link up
Redmine Bug#1966
IAM ->
<-REL
<-ACM
<-ANM
ACM sets the reset flag
ANM sets the group reset flag
when both reset flags are set we got into infinite loop
src/ftmod/ftmod_sangoma_ss7/ftmod_sangoma_ss7_handle.c
cc1: warnings being treated as errors
src/ftmod/ftmod_sangoma_ss7/ftmod_sangoma_ss7_handle.c: In function
'handle_con_ind':
src/ftmod/ftmod_sangoma_ss7/ftmod_sangoma_ss7_handle.c:255: warning: format '%x'
expects type 'unsigned int', but argument 3 has type 'U32'
make[6]: *** [ftmod_sangoma_ss7_la-ftmod_sangoma_ss7_handle.lo] Error 1
cpg_on_progress_media is default to TRUE if not xml option exists.
transparent_iam_max_size added to ccspan. Gloal value is used
if transparent_iam_max_size is not in ccSpan.
Fixed hw alarm handling: physical ids were not used which caused alarms
read wrong.
Tested sip hold
Group blocks/unblock
Group reset
Link down-> block -> unblock
FS start with link down then link up
FS start with link up, take link down and up -> make incoming call
Moises Silva
James Zhang
William Adam
Nenad Corbic
root